BLAG Forum Index
Post a reply
[quote="JacobNottingham"]Hi, im new to linux, just installed blag 90k on my laptop but im having trouble doing anything as i cannot connect to the internet! my only available connection is wireless and i have a Netgear Rangemax WN511b adapter. I really need help getting this set up so i can install packages and sort out other issues (see ntfs issues posted earlier!). I know i need the b43-fcutter tool but im not sure how to install it without the internet. can anyone help? Thanks in advance[/quote]
Disable HTML in this post
Disable BBCode in this post
All times are GMT
Select a forum
Posted: Fri Jul 25, 2008 9:23 am
Don't build it as they explain it on their site, get it prebuilt from
Posted: Tue Jul 22, 2008 2:15 pm
punting to slaveware as it looks like ndiswrapper thread now.
Posted: Tue Jul 22, 2008 11:31 am
Ok thanks for the help, this ndiswrapper looks like what i need however, when i run make distclean during installation i get this error:
Makefile:23: *** Kernel tree not found please set KBUILD to configured Kernel. Stop.
make : Leaving directory '/ndiswrapper-1.53/driver'
make: *** [clean] Error 2
Any ideas why?
Posted: Mon Jul 21, 2008 11:00 pm
[quote="JacobNottingham"]Speedtouch USB ASDL PPP connection to Wanadoo[/quote]
depending on the model of Speedtouch you might just need a regular ethernet cable like the guys already suggested above, connecting your modem and the puter. USB based ppoe connection via linux is a pain in the neck to setup. struggle a little with ndiswrapper, this will be easier then usb route.
Posted: Mon Jul 21, 2008 8:20 pm
Looks like your wireless card unfortunately has a broadcom chipset. This will make things
You'll need to install the ndiswrapper package on your laptop and install the windows drivers for your laptop using that.
Posted: Sun Jul 20, 2008 2:11 pm
I was a little confused by your suggestion: The internet connection im using has a connection from the phone line to the modem and then a usb connection from modem into the computer.
On my laptop I tried connecting a seperate ethernet cable straight to the phone line and also plugging in the usb connection to the modem. Heres what it gave me with either connection:
eth0 Link encap:Ethernet HWaddr 00:0F:1F:B9:44:C4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:19 Base address:0x1800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3370 errors:0 dropped:0 overruns:0 frame:0
TX packets:3370 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:186516 (182.1 KiB) TX bytes:186516 (182.1 KiB)
Hope that helps
Posted: Sun Jul 20, 2008 1:42 pm
Plug your ethernet wire into your laptop. You should get an orange and green light flashing to signify that the lappy is getting some signals from the router/modem. You can then type /sbin/ifconfig in a terminal and show us the results.
Posted: Sun Jul 20, 2008 1:02 pm
i do have an ethernet port on my laptop but im just as clueless as to what to do with it? The computer im using at the moment is using a Speedtouch USB ASDL PPP connection to Wanadoo broadband but it is not my connection. is it possible to temporarily use that to sort out wireless? will it require alot of setting up?
Saint of Killers
Posted: Sun Jul 20, 2008 12:47 pm
You don't have an ethernet port you can jack into?
Posted: Sun Jul 20, 2008 11:13 am
Post subject: No internet access! Help needed!
Hi, im new to linux, just installed blag 90k on my laptop but im having trouble doing anything as i cannot connect to the internet! my only available connection is wireless and i have a Netgear Rangemax WN511b adapter. I really need help getting this set up so i can install packages and sort out other issues (see ntfs issues posted earlier!). I know i need the b43-fcutter tool but im not sure how to install it without the internet. can anyone help? Thanks in advance